www.rgv.ru

[Гость]

Exactly how to cut a new doorway in an internal brick wall<br /><br /><br />In the event that it is a load-Bearing wall structure, or if you are undecided, it is critical to confer with your local<br /><br />Specialist building inspector first. <br /><br />Draw the new opening on the wall and remove any skirting.Calculate the proposed door width, which includes both legs of the lining, plus 25mm.Calculate and mark out the height, making it possible for the lining plus 10mm tolerance. <br /><br />Sketch out the location of the lintel, providing about 15mm for the bedding and packing under each end.Lay dirt sheets on each side.Cut out the plaster as neatly as possible.Cut a opening in the hub of the entrance, about 150mm above where the lintel will be, making use of the drill, then the hammer and bolster.Thread the needle through.Support it on each area, 500mm from the walls with the adaptable props set down onto the scaffold boards. <br /><br />Trim out the position for the lintel and insert it, bedding it up with rigid mortar blended one part cement to three parts fine sand, packing it tight with pieces of slate inserted into the mortar.Leave over night. <br /><br />Slice out the rest of the opening.Drill holes at intervals down the sides.Starting off at the top and slicing downwards with the bolster, cut out and clear away the bricks and part bricks.Light-Weight blocks can be sawn.Use a hand-Held bottle of spray to prevent the dust going everywhere when the hole is cut, clear up the dust before moving on to the next phases.Remove the props and needle. <br /><br />Help make up the lining by attaching the two legs To the head, allowing for for 2mm all around for door clearance.As an alternative, use ready-To-Assemble linings with the head rebated to receive the legs. <br /><br />Resolve the latch leg to the brickwork by drilling throughout the lining directly into the brickwork and working with the frame fixings.Check for level in all planes, taking the leg out with slate or hardwood where required. <br /><br />Deal with the hinge leg of the lining in the exact way, using wood-Packing pieces and changing for up and down in all planes and also level on the head.Fill in behind the lining with mortar and leave to set.Refit the skirtings, ceasing at the point where the architrave will start.If you need to make the plaster, do this ahead of installing the architrave. <br /><br />Help to make good the needle hole with some of the old bricks and repair the plasterwork.Mitre the sides of the architrave using the mitre block.Add the architrave to the lining to cover up the cut-Aside plaster and the join between that and the lining. <br /><br />At this stage your finished and you can pat yourself on the back for a job will done. <br /><br />For a job of this type you will first need: <br /><br />A hammer<br /><br />A club hammer<br /><br />A lintel(Pre-Stressed cement with 150mm bearing on each side) <br /><br />A few pieces of slate<br /><br />2 short scaffold planks<br /><br />Sand and cement<br /><br />Ready-To-Assemble doorway linings or 25mm x wall thickness planed all round timber for doorway liner<br /><br />New architrave<br /><br />Steel sleeved frame fixings<br /><br />Packing pieces(Wood offcuts) <br /><br />2 flexible pink nfl jerseys steel props<br /><br />150mm x discount sports jerseys 100mm timber support needle, 1.5m long<br /><br />Lost head nails<br /><br />A cheap custom nfl jerseys further masonry bit suited for the frame fixings<br /><br />A spirit level<br /><br />A mitre block<br /><br />A bolster<br /><br />An electric drill with a 20mm masonry bit 150mm long<br /><br />A saw<br /><br />